Surbiton Tolworth - Laptop Repairs Computer Support and Data Recovery
Contact SOS Computer Fix
Copyright © All rights reserved. SOS Computer Fix  
0208 330 7113
SOS Computer Fix - Repairs and Support

www.soscomputerfix.co.uk    

Home.Computer Services.Data Recovery.About Us.Area Covered.Contact Us.

SOS Computer Fix, Hazel Bank, Surbiton, Surrey, KT5 9RH

Tel: 0208 330 7113

Computer Repairs and Support Services for the home and office

Sitemap

E-Mail :

Privacy Policy

 

1. Media Issues: Where the drive has developed bad sectors, making it difficult or impossible to access via any Windows based operating system. This can be most commonly diagnosed by the fact that the hard drive is seen correctly in the BIOS (i.e. Correct Model number and capacity) and the computer locks up (freezes) when you try to access the drive. In this case a sector-by-sector image of your entire drive must be made onto a known good drive, then specialist software must be used to extract your data from this image. We have various specialist cloning facilities, including Deepspar Disk Imager, costing thousands of punds each, which uses combinations of soft / hard resets of the drive, as well as powering the drive down if necessary, to ensure the best possible image of the faulty drive.

 

2. Electronic Failure: Where the logic board (PCB) has failed or died. This can be most commonly diagnosed by a completely dead drive, burning smell or making clicking noises. In this case a perfectly compatible PCB has to be located to re-enable access to the drive. This is NOT a simple matter, as nearly all drives have ROM (Mainly WD & Seagate) or NVRAM (IBM/Hitachi) information programmed into the PCB itself. This information has to be read off to a file, and then re-programmed into the donor PCB. This requires specialist hardware & software, again costing many thousands of dollars, to do this. In some models, such as Toshiba laptop drives, this ROM info is absolutely UNIQUE to the drive and so the original PCB must be repaired to facilitate the recovery. We have surface mount and hot-air soldering facilities to do this. Also, more often that not the electronic failure has also caused partial media problems (bad sectors), so an image needs to be made and worked from (see above Category 1 failure)

 

3. Firmware Failure: This is where some modules of "firmware" on the actual platters of the drive has become damaged or corrupted. The drive requires these modules to the read from the Service Area (SA) of the drive, before it will start up and become ready. This often manifests itself by the drive spinning up as normal and sounding OK, but is inaccessible in the PC's BIOS. It may be seen as it's factory alias (e.g. "Athena" for some Maxtor drives, or "HAWK" for some WD models). To recover from this requires extremely specialist hardware and software (such as from ACE Laboratories or Salvationdata), plus years of experience and technical knowledge to repair the SA. This requires great skill and resources (such as replacement modules from compatible stock/library drives), as one small error can render your drive irrecoverable. Likewise, more often than not, the firmware failure has also caused partial media problems (bad sectors), so an image needs to be made and worked from (see above Category 1 failure), especially in cases where the "G-List" (Growing defect list) has been damaged or corrupted.

 

4. Physical Failure: In this case, a physical fault is preventing your drive starting up. This can range from a single failed head, through complete head stack failure, to motor failure. A single head failure can be diagnosed when the drive ID's OK and starts to image well, but in patches (e.g. The DeepSpar Imager may image 150,000 sectors perfectly, then 50,000 inaccessible, and so on. In this case 1 of 4 heads has failed). A complete head stack failure usually manifests itself by clicking from the drive when it is started up. In the case of head failure, your drive needs to be disassembled in a dust-free cleanroom environment and the offending heads removed. Then the replacement heads need to be fitted, this is an EXTREMELY skilled job. Replacement heads are also very difficult to locate sometimes, due to compatibility issues, so large resources and vast product knowledge is required. Fortunately we have thousands of spares in stock, and access to worldwide partners to locate the more difficult to find parts. In the case of motor failure, this is usually shown by the drive not spinning up at all, or making a quiet buzzing sound. In most cases, a motor failure requires the heads and platters to be removed and placed into a wood working chassis. Once more, great skill, techniques and specialist equipment are required to do this. Finally, more often that not, the failure has also caused partial media problems (bad sectors), so an image needs to be made and worked from (see above Category 1 failure).

 

 

Hard Drive Failure

 DATA RECOVERY QUOTE

Contact Us
data recovery on external hard drives in new malden, chessington, esher, thames ditton, sutton or raynes park